ULTRALIGHT ANTWEIGHT PACKAGE
This package is intended to get you jump-started, saving you the time involved in hunting around for all the right parts before even starting to build.

These parts are selected to work well for a four-wheel-drive, 1 pound robot. With this complete package, you will have all the main components ready to go*. Simply hook everything together, and you'll be driving your bot around soon!

For a battle-ready antweight, all you'll need to provide on your own, beyond this package, are the following items (all of which you could pick up at your local hardware store and electronics store):

- Fasteners (nuts, bolts and wire connectors) Don't be afraid to use hot glue or even duct tape on your antweight!
- A weapon (optional)

 

Ultralight Antweight Chassis
Looking for a perfect solution for a rugged, low-profile and light-weight Antweight (1 pound) robot chassis? You've just found what you need.

These Antweight Chassis are just what you need to incorporate all the components into one compact, one-piece chassis, with integrated motor supports, wheel guards, and large center bay for your electronics. A full 4 wheel drive mobility base can built for only a few ounces.

These Chassis were designed for use with the Sanyo NA-series gearmotors, usually in 4WD configuration.The new Treaded Drive Base Kit is used to make your own treaded robot powered by four motors. This new base design incorperates the new motor mount design which uses a wide screw head to securely mount the motor. Read more about the drive base here.

Drive Base includes:
5/8" billet machined aluminum body
Four 100:1 extra long shaft gear motors
4 direct mount wheels and treads
1 acrylic laser cut lid kit with screws (not shown)
Motor mount screws

Surveyor Wheel Set
These custom turned aluminum wheels made for our small robot chassis like Surveyor (or any 3mm shaft). They are great for the Sanyo NA style motors used on Surveyor as well as 3mm shaft Copal and BaneBots motors . The wheels come complete with a super grippy all terrain rubber tread, and a stainless set screw for fixing it to the shaft (accessed under the tread with a 1/16" hex wrench). While these will work with round shafts, they get the best purchase on a shaft with some sort of a flat on it. They are machined from 6061 aluminum and anodized black. Read more about these wheels here.
100:1 Micro Geared Motors x4
These are just amazing little motors for their weight. With one at each of your four corners you are always guaranteed good traction and speed. These have a special long shaft with a "D" cut into it for the outer 10mm to ensure full engagement and proper spacing of our tank tread wheels. Read more about these motors here.
Sabertooth 5 Speed Controller
To control the above motors, you need a good speed controller. This dual channel controller hooks to both motors and your radio receiver together, providing single stick operation without an expensive transmitter with an onboard computer. This controller includes two soldered RC connectors as pictured. Read more about this controller here.
7.4V LiPoly battery
This Antweight kit will run great with this 7.4V, 2 cell, 800mah Lithium-Polymer battery pack. This is a great, high quality and very lightweight battery. Read more about these batteries here. Please note you MUST use a LiPoly charger for this battery!

GWS GWT-4A 75Mhz Radio Control System
You need a good radio to drive your antweight robot. As a great, simple-to-use 4 Channel FM Surface Radio System, this radio is a great start for beginner or those on a budget. It is our lowest-priced radio system, but doesn't lack in power. Read more about this system here.

GWS 4-Channel Pico Receiver
This is the very tiny GWS 75Mhz 4-channel receiver that is taking the small combat robot world by storm. Tiny and very lightweight at only 4.4 grams! Also tested in many combat robots and is extremely shock-resistant. Futaba negative shift style. Read more about this receiver here.

GWS Crystals
These are the crystals you will need to use with the above radio system and receiver.

If you order your system with "No channel Preference", we will randomly select a channel number for you from those we have in stock. Although we strive to have all the channels in stock, some may be special order, and may take up to a week to arrive.

Please be sure to deselect the crystals if you upgrade to a 2.4GHz system.
Thunder Power TP610C-ACDC 1-6 Cell LiPo AC/DC Charger with Balancer
You need a special charger to recharge LiPoly batteries. This charger is a great inexpensive solution. The Thunder Power RC TP610C-ACDC charger is the long-anticipated and fully integrated AC/DC version of the popular TP610C. Read more about this charger here.
No longer available as a package.

*Please check the rules of the competition you are intending to enter, additional requirements may apply for specific events.

Building and operating a combat robot can be dangerous. Please use extreme caution when operating your power tools and any robot components.